Bargain Center: discussion, gossip, etc.

[pekbro]

Found a code for Evolve Alloy Lite from Excite Audio: FSTH25

https://www.pluginboutique.com/product/ ... Alloy-Lite

It's not free for some reason, the cost came out to $0.66, though you can use v-cash to bring the cost to $0...

Anyway, you can upgrade to full version from this for $20 if desired...

[Ou_Tis]

Found a code for Evolve Alloy Lite from Excite Audio: FSTH25

https://www.pluginboutique.com/product/ ... Alloy-Lite

It's not free for some reason, the cost came out to $0.66, though you can use v-cash to bring the cost to $0...

Anyway, you can upgrade to full version from this for $20 if desired...

So you could use it to get this month's freebie, "Gainstage Pro"... which unfortunately seems a bit pointless. As I understand it when recording you should set preamp gain as loud as you can without clipping, to minimize the signal to noise ratio. Gaintsage Pro indicates whether it's too quiet or too loud (I'd assume they do the latter by checking whether it's clipping). IDK if it judges "too quiet" by the noise floor or just by gain.

[Ou_Tis]

So you could use it to get this month's freebie, "Gainstage Pro"... which unfortunately seems a bit pointless. As I understand it when recording you should set preamp gain as loud as you can without clipping, to minimize the signal to noise ratio.

Oh I see it also has settings for things like "hard compression" or "light saturation" to gainstage for when going into most plugin emulations of typical corresponding hardware.

[pekbro]

So you could use it to get this month's freebie, "Gainstage Pro"... which unfortunately seems a bit pointless. As I understand it when recording you should set preamp gain as loud as you can without clipping, to minimize the signal to noise ratio.

Oh I see it also has settings for things like "hard compression" or "light saturation" to gainstage for when going into most plugin emulations of typical corresponding hardware.

Thx, I got that last night when purchasing the Fuse Audio Ocelot plugins that I had missed at release, well missed is not really correct, as much as I wanted to support Ray, I didn't really need the upmixer or the octaver and I knew they would be available at PB for cheaper than release at some point. That point came pretty quickly since they are currently $15 ea, e.g. %50 lower than release.

Hopefully Ray is ok with that since they tend to undercut his own pricing by a large margin.
Sry Ray, but I got to save where I can, I bought the clipper and limiter direct at least.

https://www.pluginboutique.com/search?q ... ses%5B%5D=

[Uncle E]

Is this still a good and relevant tool Nowadays?
the price would be right

Sonnox released Claro in 2021. It’s still good and relevant.

- edit - sorry, please ignore this. Bad reading comprehension on my part.

[agharta]

Is this still a good and relevant tool Nowadays?
the price would be right

Sonnox released Claro in 2021. It’s still good and relevant.

They were referring to Codec Toolbox which was released about twelve years ago.

[Howie62]

Many thanks for this code!

Found a code for Evolve Alloy Lite from Excite Audio: FSTH25

https://www.pluginboutique.com/product/ ... Alloy-Lite

It's not free for some reason, the cost came out to $0.66, though you can use v-cash to bring the cost to $0...

Anyway, you can upgrade to full version from this for $20 if desired...

So you could use it to get this month's freebie, "Gainstage Pro"... which unfortunately seems a bit pointless. As I understand it when recording you should set preamp gain as loud as you can without clipping, to minimize the signal to noise ratio. Gaintsage Pro indicates whether it's too quiet or too loud (I'd assume they do the latter by checking whether it's clipping). IDK if it judges "too quiet" by the noise floor or just by gain.

[Download SOphist]

Found a code for Evolve Alloy Lite from Excite Audio: FSTH25

https://www.pluginboutique.com/product/ ... Alloy-Lite

It's not free for some reason, the cost came out to $0.66, though you can use v-cash to bring the cost to $0...

Anyway, you can upgrade to full version from this for $20 if desired...

thanks mate!

[Howie62]

Couldn't activate, limit reached, thanks for posting though.

Found a code for Evolve Alloy Lite from Excite Audio: FSTH25

https://www.pluginboutique.com/product/ ... Alloy-Lite

It's not free for some reason, the cost came out to $0.66, though you can use v-cash to bring the cost to $0...

Anyway, you can upgrade to full version from this for $20 if desired...

[rtoip]

---

[WaveRites]

Couldn't activate, limit reached, thanks for posting though.

Found a code for Evolve Alloy Lite from Excite Audio: FSTH25

https://www.pluginboutique.com/product/ ... Alloy-Lite

It's not free for some reason, the cost came out to $0.66, though you can use v-cash to bring the cost to $0...

Anyway, you can upgrade to full version from this for $20 if desired...

The code for Evolve Alloy Lite works (again). I just bought it for €0.02 and also got the freebie (Gainstage Pro).

[Howie62]

Yep, bought it, got my code, downloaded and installed. Went to activate and got a message saying words to the effect limit reached for the code..

Couldn't activate, limit reached, thanks for posting though.[quote=pekbro post_id=9113857

What do you mean ? You managed to purchase it with a coupon, but the plugin manufacturer didn't allow you to activate it ?

[Uncle E]

They were referring to Codec Toolbox which was released about twelve years ago.

Thanks! Edited my post.

[rtoip]

delete

[Howie62]

Emailed PB support, will let you know what they have to say..

Yep, bought it, got my code, downloaded and installed. Went to activate and got a message saying words to the effect limit reached for the code..

Couldn't activate, limit reached, thanks for posting though.[quote=pekbro post_id=9113857

What do you mean ? You managed to purchase it with a coupon, but the plugin manufacturer didn't allow you to activate it ?

Thanks for the warning - I was about to buy it but I'll hold off.