Omnisphere 3

[muzicxs]

Has anyone managed to pay with CC? Support acknowledged there were payment issues, but other than that they're not able to help in any way. Their recommendation: use PayPal. Absolutely mind boggling...

Yes I had no problem once I had authorised payments from Spectrasonics in my banking app

That's good to know, thanks! I'll try again once I have my money back. Which could take up to 25 days according to my bank.

[aMUSEd]

Has anyone managed to pay with CC? Support acknowledged there were payment issues, but other than that they're not able to help in any way. Their recommendation: use PayPal. Absolutely mind boggling...

Yes I had no problem once I had authorised payments from Spectrasonics in my banking app

That's good to know, thanks! I'll try again once I have my money back. Which could take up to 25 days according to my bank.

One problem is on most payment sites when you need to authorise payment through the banking app I get a popup prompting me to do this, but the Spectrasonics shop doesn't do that, I had to figure out for myself to check my banking app which told me payment had failed because it needed authorising and do I want to do that now? Once I had done that it went through but I think their store is not fully conforming to certain standards.

[muzicxs]

One problem is on most payment sites when you need to authorise payment through the banking app I get a popup prompting me to do this, but the Spectrasonics shop doesn't do that, I had to figure out for myself to check my banking app which told me payment had failed because it needed authorising and do I want to do that now? Once I had done that it went through but I think their store is not fully conforming to certain standards.

In my case it was complaining about an AVS mismatch, which didn't make sense because the address matched exactly!

To be honest, the inability for support to help me out left a bad taste.

[Funky40]

Maybe I took a factory pad sound from the "Ambient Dreams" section. Maybe I changed the envelope to have a much sharper attack and swapped out the filter, then changed the reverb and added a compressor

it HAS to be possible to save an altered factory preset at same location !
Cause: maybe i just adjusted the Reverb slightly and nothing else, no ?

But you can do that if you want to. You just click save as. It will default to saving in Steam>>Omnisphere>>Settings Library>>Patches>>User

You don´t seem to understand me.
What you´re telling me says: No, you can´t ( as a fact).....but you tell me on the other hand: you can ? No, you can´t. You just made the point yourself

When i change a factory preset sound slightly, just adjustimg the Reverb for example slightly, then is it "for me" (for my brain) still that factory preset and NOT a user preset .


I had the Korg Kronos. There was i able to do that. Readjust something like just the Reverb, Quick SAVE. Donne. That´s what i like. Easy business

[BJ]

Do they removed the hardware section ?

The hardware library is still there

[SamDi]

Sorry, if it was already discussed. This thread is growing faster, than I can read. But

Is it normal, that I need to choose libraries and categories again and again after each restart? Why not just "All" is set for both?

Other strange thing: after initialize patch, the filter ENV shows some middle values on attack, decay, sustain and release. Why not A and R short before 0 and S full on, the same as on amp ENV or Omnisphere 2?

[jbraner]

Is it normal, that I need to choose libraries and categories again and again after each restart? Why not just "All" is set for both?

It seems to be - unless somebody knows better...

[jbraner]

/snip
This is a great case for the "Attributes" tag

https://support.spectrasonics.net/manua ... ags-page01

And the assignments tag
https://support.spectrasonics.net/manua ... ags-page01

You would create an attribute called "User Tweaked Presets" or whatever

I'll need to play around with this.
The "attribute" is the folder that you save your user preset in.
If I add "attributes" and "type" during "save preset as" - they don't stay. IOW if you reload the patch and "save as" again - the attribute you just added isn't there any more.

I don't doubt that I'm doing something wrong - I'll play some more tomorrow.

[SamDi]

And I think, I found a bug:

When the signal path is set to independent, the global AMP and FIL ENV controls should add an relative offset, to e.g. layer A and B, according to the manual. But if you set same values on them and then change the global ENV value, e.g. Attack they seem to jump on different levels. Often the value of layer B is then set to 0 (randomly?), although it shouldn't according to the offset logic. It seems like pretty random behaviour. Can anybody confirm this or is it a misunderstanding or not-consideration of a side effect on my side?

[noddog]

Anyone know how to select your MIDI controller as default? It seems like you need to select your MIDI controller again every time you open Omnisphere.

[SamDi]

Anyone know how to select your MIDI controller as default? It seems like you need to select your MIDI controller again every time you open Omnisphere.

Did you try "Save as Default Multi" from the main menu?

[noddog]

Anyone know how to select your MIDI controller as default? It seems like you need to select your MIDI controller again every time you open Omnisphere.

Did you try "Save as Default Multi" from the main menu?

Yes, this works, thanks. It's a little odd that the MIDI controller selection is called a Multi.

[SamDi]

Yes, this works, thanks. It's a little odd that the MIDI controller selection is called a Multi.

Yeah one could consider this odd. In Omnisphere 2, you had to even do this, to make magnification factor persistent.

[noiseboyuk]

Is it normal, that I need to choose libraries and categories again and again after each restart? Why not just "All" is set for both?

It seems to be - unless somebody knows better...

There is a setting to optionally recall the previous state, but that's all. There's no way to set a permanent default.

[cryophonik]

I think "Multi" is simply referring to the default state of Omni when you open it; i.e., it is set up for multiple parts.