Some requests, bugs and questions

[jmg8]

Hello Vojtech.

Are we able to add a midi modulator that can add velocity, after touch, keyboard tracking, mod wheel, pitchbend etc.

In MPowerSynth in the modes section for osc 2 and 3 is it possible to add a spectral morph option, so we can morph between osc1 and osc 2/3?

Is ultra maximizer coming to MXXX?
I understand it's a multiband limiter, maybe there is an active preset for this coming?

When holding ctrl and moving HP LP filters in EQs it inverts the movement instead of being fine tune.

Randomize in multiparameter banks doesn't behave correctly. It only changes values a few times every severel clicks and changes parameter assignments.

Is it possible to send data between plugins (like multi analyser) for example: I could insert plugin signal sender on vocal and drums and then use the sent information to duck guitar/piano. Like sidechain but more than one at once. Not actually audio but data collected on the source channel itself sent to other plugin versions. Just like it works in MMultiAnalyser.

Help files for all plugins within MXXX. At the moment I have to visit the website fo find pdf doc for each individual plugin.

Is it possible to interpolate between impulses in convolution? For example I could use the test tone record feature to sample an eq and various frequencies and gain values and then use interpolate to move (somewhat) smoothly between them.

What part of the wavefom is used when importing a sample into an oscillator? The pdf help just says part of the sample is used. I assume it takes a single cycle waveform. Are we able to have any control over where in the sample this is taken?

Thanks!

[ZentralmassivSound]

I can answer a few of these I think:

Are we able to add a midi modulator that can add velocity, after touch, keyboard tracking, mod wheel, pitchbend etc.

That's already there in the MIDI setup (button at the lower right corner). Or do I misunderstand you?

Randomize in multiparameter banks doesn't behave correctly. It only changes values a few times every severel clicks and changes parameter assignments.

I noticed and reported this, too. I think Vojtech is working on it.

Help files for all plugins within MXXX. At the moment I have to visit the website fo find pdf doc for each individual plugin.

You have the "?" symbol for help in each plugin section of course, but I agree sometimes it's better to have the whole documentation as one pdf/website to read.

Is it possible to interpolate between impulses in convolution? For example I could use the test tone record feature to sample an eq and various frequencies and gain values and then use interpolate to move (somewhat) smoothly between them.

Did you try the A/B feature? It's just a fader, but it may be sufficient.

What part of the wavefom is used when importing a sample into an oscillator? The pdf help just says part of the sample is used. I assume it takes a single cycle waveform. Are we able to have any control over where in the sample this is taken?

The normal mode custom sample load takes the whole file as one wave cycle.
The harmonics mode sample analyzer takes only a window of the file, which you can configure, also interpolation etc.

[DarkStar]

You can download all the PDFs in a single zip file here:
http://www.meldaproduction.com/download ... ations.zip
(link at the bottom of many of the web site pages)

Or individually, form this page:
http://www.meldaproduction.com/download ... tation.php

[MeldaProduction]

In MPowerSynth in the modes section for osc 2 and 3 is it possible to add a spectral morph option, so we can morph between osc1 and osc 2/3?

What do you mean by that? You are describing simple mixing, that's the default mode.

Is ultra maximizer coming to MXXX?
I understand it's a multiband limiter, maybe there is an active preset for this coming?

Nope, sorry. But it's possible to program it of course.

When holding ctrl and moving HP LP filters in EQs it inverts the movement instead of being fine tune.

Damn . It actually is finetuning, but in wrong direction .

Randomize in multiparameter banks doesn't behave correctly. It only changes values a few times every severel clicks and changes parameter assignments.

It depends on what's the target. It uses smart randomizer, but for some parameters (e.g. step sequencer values) it just doesn't work well, too deep structure. Hold Alt when pressing the button and you'll get a full randomizer.

Is it possible to send data between plugins (like multi analyser) for example: I could insert plugin signal sender on vocal and drums and then use the sent information to duck guitar/piano. Like sidechain but more than one at once. Not actually audio but data collected on the source channel itself sent to other plugin versions. Just like it works in MMultiAnalyser.

That's actually impossible in many cases, long story... Let's just say there are physical limitations . I don't understand how is it related to MXXX anyway.

[jmg8]

In MPowerSynth in the modes section for osc 2 and 3 is it possible to add a spectral morph option, so we can morph between osc1 and osc 2/3?

What do you mean by that? You are describing simple mixing, that's the default mode.

Well crossfading is deferent to spectral morphing. I want to be able to scan between two waveforms like wavetable synthesis. I know that can be done with the oscillator when morphing to custom shape or step sequencer, but I want to be able to morph between two imported wave shapes. Mixing the will sound like there are two waves playing, whereas spectral morphing will sound like its one wave changing shape.

Is ultra maximizer coming to MXXX?
I understand it's a multiband limiter, maybe there is an active preset for this coming?

Nope, sorry. But it's possible to program it of course.

How many bands does your ultra maximize use? do you have the limiters on clean mode?

When holding ctrl and moving HP LP filters in EQs it inverts the movement instead of being fine tune.

Damn . It actually is finetuning, but in wrong direction .

Randomize in multiparameter banks doesn't behave correctly. It only changes values a few times every severel clicks and changes parameter assignments.

It depends on what's the target. It uses smart randomizer, but for some parameters (e.g. step sequencer values) it just doesn't work well, too deep structure. Hold Alt when pressing the button and you'll get a full randomizer.

Cool, thanks, I didn't know about holding alt. But still if I have assigned a multiparameter to various parameters, I don't want these to be randomized, only the values for the bank.

Is it possible to send data between plugins (like multi analyser) for example: I could insert plugin signal sender on vocal and drums and then use the sent information to duck guitar/piano. Like sidechain but more than one at once. Not actually audio but data collected on the source channel itself sent to other plugin versions. Just like it works in MMultiAnalyser.

That's actually impossible in many cases, long story... Let's just say there are physical limitations . I don't understand how is it related to MXXX anyway.

Neither do I, I didn't mention MXXX.

Thanks, Vojtech