MXXX: "Free" mode point curvature seems to only allow Y control over (x,y). Example preset included.

[Annabanna]

I generally use "free" mode in the points properties panel because it allows steeper curvatures and greater control than modes 1 or 2, but there's a problem:

The example below shows what happens when I try to use MP1 to control Point 1's curvature on a waveshaper. 1, it only moves it on the Y axis. Going through the folder tree of available parameters, there doesn't seem to be any other way to move it on it's x axis. There is only a single "curvature" option, and that only controls the Y axis, so it's always stuck on wherever it was last moved manually for it's x value.

1) Is there a way to properly control curvature in "free" mode? (both x and y axis)

2) If not, I'm having a dyslexic moment, so... if I ONLY need to control the X axis, and not the Y, is there some way to maybe use the MP's "transform shape" feature or similar to effectively rotate the graphs such that the Y control I do have translates to x control?

Code: Select all

$eNqVVE1P4zAQvfMrRrPXpXFKgVRKgqCiKyQKUbML3aM3maYRjh3ZTmn59SvnA2jRHvZijd+MZ57fjB1e7SoBW9KmVDJCf8QQSGYqL2URYWPXpwFexSfhYrVaGbK2lIWBbxH6CDMlrVZCkDa3kv8RlEfIEG7z0iqdlm8UIft+ANxys+-B+2Vai9Jaah1+hP7Z+PIYHrd1Fnx3P3+8ESp76bIGX7DH9VqUsneRJW1mSgheG8pTS5pUl6gRtky45tVhSEs7JUGZpTwRTVHKnuXToMt07F8whnHYuc1gwA2XLzPVSNtJ0mhN0jqw3c8bIR54RRE+8y2lG16TBh-hGENYtSR+uzUO3XnmDTXSQ9n-T444LDSvN3GYqFJayCJko4AFCNnOmYxNLi-8abcizAUvzE2E-sRH+LmvKcK5JgIfvSHDv0Ng1-Lbu9WLQ68v7B3e4h14N4wbr8PWxEcAgx+-7ro5WqjczcWD0hUX6PCUV7RUr62Azvvh7GTuePuQVkrZjSRjENKa+r4-cdG4SR1N2aTfdUkS0hlJa1zTBx5tQ5dcFhThBOEd-9pjOIXWhFMY6meN3nLbaELoU7DROTsfn-kXwZQFwQeXVr4jBb4gTrbrzJZbSjQZsuBeV5ppInn0BNq2OPWcEYczbqlQen9nqbqTawUJN+ZV6TxCV7if4V48h1wnXQXH6nNFR0DXsOSWIhxjHC641eXuU7CuXW9bNuM4fC5zu1nEYaoanREkmtalsKTbr6a79BDiDYdOQu-T12Pik79dEIQw

[Annabanna]

I just noticed there seems to be the same issue with the "smoothness" parameter. Animating it only works if the sides are locked. Since there is only one parameter, I'm not seeing a way to smooth the L or R side only when sides are unlocked.

Is there a way around this?

EDIT: And I guess I don't see a way to control the custom shapes in any of the envelopes either. Whether in the Modulators, or in the built in envelopes in MSF, etc is there any way to control points?