KVR Audio

tacitus · Post by **tacitus** » Fri May 06, 2005 12:39 pm

Hi all, I was wondering if there is a VST Filter with the Low Pass & High Pass on the same controller? Like the Stylus RMX filter. So that you can use one knob/slider without having to use a sepparent switch to toggle between them.

Eg. midi values 0-63 activates & controls the low pass & midi values 64-127 cover the hi pass.

Thanks.
I would love it if you could do this with Quad Frohmage!

2windy · Post by **2windy** » Fri May 06, 2005 1:06 pm

Not sure quite what you mean but Super CamelPhat may do it. Set high, set low and lock filter. Any movement sweeps both.

If not please ignore everything I just said

sirocco · Post by **sirocco** » Fri May 06, 2005 1:11 pm

betabugs bugpass maybe?

tacitus · Post by **tacitus** » Fri May 06, 2005 1:22 pm

What I am after is a filter where the cutoff knob controls only the lowpass from hard left knob position to centre (where it gets turned off). Then only the high pass filter kicks in at knob positions centre to hard right.

Is is for my controller surface so I don't have to use a separate control for selecting between LP & HP.

jmp909 · Post by **jmp909** » Fri May 06, 2005 1:23 pm

he means the slider is split like this

[LPF] <----- [no filter] -----> [HPF]

if you move left from the middle it lowpasses the signal, if you move right from the middle it highpasses it...

this is on the Easy Edit page in Stylus RMX.

rbet · Post by **rbet** » Fri May 06, 2005 1:28 pm

it is on the moonclass vst too... I think.

tacitus · Post by **tacitus** » Fri May 06, 2005 1:29 pm

Thanks for the clear explaination jmp909!

jmp909 · Post by **jmp909** » Fri May 06, 2005 1:35 pm

i could make this in synthedit. probably.

multree · Post by **multree** » Fri May 06, 2005 1:38 pm

jmp909 wrote:he means the slider is split like this

[LPF] <----- [no filter] -----> [HPF]

if you move left from the middle it lowpasses the signal, if you move right from the middle it highpasses it...

this is on the Easy Edit page in Stylus RMX.

well bugpass is about that if you reverse the sliders.... it can either be (locut)sound(hicut) or sound(lopass)(hipass)sound

tacitus · Post by **tacitus** » Fri May 06, 2005 1:42 pm

I was after resonance as well though, thanks.

tacitus · Post by **tacitus** » Fri May 06, 2005 1:48 pm

I can't download Bugpass for some reason.

jmp909 · Post by **jmp909** » Fri May 06, 2005 3:37 pm

try this... its mono signal.. and i havent even tested it (you'll have to wait till i get home)... but if its close i can work on it...

www.interference.co.uk/test/lpf2hpf.dll

all i can tell you is it uses the SVF filter from synthedit

flanneljammies · Post by **flanneljammies** » Fri May 06, 2005 4:00 pm

Scuzzphut's EQ Killer does this rather well too... But yeah, Bugpass!

tacitus · Post by **tacitus** » Fri May 06, 2005 5:00 pm

Thanks, tried out your Synthedit plug. It's cool. Just what I wanted!

jmp909 · Post by **jmp909** » Fri May 06, 2005 5:15 pm

great. if i get time (probably not till next week) i'll get onto sorting out the Filter range and make it midi controllable.

one thing someone mentioned is that there may be some "zippering"/glitch when you switch over filters.... (it doesnt really crossfade it just switches as you go past the middle... well actually it just sticks one at Volume 0 and the other up)

let me know anyway.

bear in mind i'm learning so whilst i'm up for suggestions I cant give you any guarantee of timescale or quality

thanks
j

VST Filter with Low & High Pass on the same controller?