Muse Research

Kermit Jagger · Post by **Kermit Jagger** » Sat Jun 10, 2006 4:26 pm

Odo Purple 2 - working

Odo SeeqOne 2 - working

Odo Dr-Fusion 2 - not working

Hybernation · Post by **Hybernation** » Wed Jun 14, 2006 8:52 pm

Exciton works.

Nice little no-frills VA that has been around for a while, and that seems to be still be well thought of here at KVR (and which I had not heard of until today).

Reboots receptor upon first launch and then works fine. Patch banks can be saved as FXB's from Sonar or Tracktion, then installed onto Receptor and work great. Some additional banks of sounds on the dev's site as well as on Patch Arena.

Hybernation · Post by **Hybernation** » Tue Jun 20, 2006 9:09 pm

Albino 3 works great as "unsupported" on Receptor. Leaves Albino2 (fully Receptorized) completely alone and functional, too.

After installed as unsupported, you can drag-n-drop all the folders under the "banks" folder to "Drop Installers Here" and install all of the FXP presets as Receptorized presets. When I did this I got the message "2072 worked 119 failed"...but hey, 2072 presets?!?!? I'm not complaining.

This thing sound pretty awesome. Of course those four-part layer patches can eat your CPU ALIVE!

Kermit Jagger · Post by **Kermit Jagger** » Fri Jun 30, 2006 3:37 am

Has anyone managed to run Oatmeal ? I'm running into the same problem as described by Hybernation regarding the GUI.

Hybernation · Post by **Hybernation** » Fri Jun 30, 2006 2:34 pm

Kermit Jagger wrote:Has anyone managed to run Oatmeal ? I'm running into the same problem as described by Hybernation regarding the GUI.

I'm emailing you a version of Oatmeal that works on Receptor. The newer versions (36-1 and 37-1) with all the nice skins do not work, apparently.

Hybernation · Post by **Hybernation** » Sat Jul 01, 2006 6:25 pm

Tone2's FireBird 1.0 works great on Receptor. Comes with three banks in FXB format, which "Receptorize" just perfectly. Very nice little synth with a flexible and sometimes unique sound.

Check it out...

Fuzzpilz · Post by **Fuzzpilz** » Tue Jul 04, 2006 7:52 am

Hey. Sorry I got around to this so late - I barely know anything about Receptor, so this is more or less a stab in the dark, but could those of you who have been having trouble with Oatmeal on Receptor try this? Just clean up, install 37-2, and replace the dll.

Post by **Ben [KVR]** » Tue Jul 04, 2006 8:34 am

Fuzzpilz wrote:Hey. Sorry I got around to this so late - I barely know anything about Receptor, so this is more or less a stab in the dark, but could those of you who have been having trouble with Oatmeal on Receptor try this? Just clean up, install 37-2, and replace the dll.

Using 37-2a - when you instantiate Oatmeal on Receptor you get loads of pop-ups along the lines of 'No background image set for page "wfe1page"!', no valid font files, no valid skin, X section missing, etc. Basically it can't find any files in its sub-folders for some reason.

Fuzzpilz · Post by **Fuzzpilz** » Tue Jul 04, 2006 9:45 am

Hmm. It can obviously find the skin file, though, or it wouldn't even get to the messages you quoted, let alone mention specific page names... does it really say "no background image set" rather than "failed to load image so-and-so"? If the files are in order, that's quite odd...

Another attempt.

Post by **Ben [KVR]** » Tue Jul 04, 2006 10:13 am

It must find the default.oms file because it displays the main background image. However for all other files it reports:

- No background image set for page "midipage"
- No background image set for page "wfe1page"
- No background image set for page "wfe2page"
- No valid font definitions found
- No valid controls defined in skin description
- Velocity curve box section missing
- Aftertouch curve box section missing
- Waveform editor 1 section missing
- Waveform editor 2 section missing
- LFO editor 1 section missing
- LFO editor 2 section missing
- XY Pad section missing

Oatmeal is then loaded, but with the background image displayed only.

Fuzzpilz · Post by **Fuzzpilz** » Tue Jul 04, 2006 10:38 am

This most likely won't work either, but it'll be more verbose about how exactly it's failing to find certain things. Sorry this is taking so long.

(Edit: Sorry, forgot a detail. Get it again if you were too fast for my correction.)

Post by **Ben [KVR]** » Tue Jul 04, 2006 10:48 am

This version gives the following, and similar:

fsetpos failed. (looking for "size=", errno: 9)
fsetpos failed. (looking for "background=", errno: 9)
etc.

Fuzzpilz · Post by **Fuzzpilz** » Tue Jul 04, 2006 10:52 am

Right, that's the general sort of thing I expected... at least I have something to go on now. Looking into how all this EBADF fun might be coming about.

Fuzzpilz · Post by **Fuzzpilz** » Tue Jul 04, 2006 11:02 am

Here. Before I try anything more annoying, I want/need to see if I run into the same problem with ftell/fseek. I suspect I will.

Post by **Ben [KVR]** » Tue Jul 04, 2006 11:28 am

The first error that occurs is now:

- Reached next section ("@page") before finding "background="

No mention of ftell or fseek. The error above appeared when using fsetpos too BTW.

Muse Research

KVR Audio

Unsupported Plugins that work on Receptor!