LennarDigital

fgimian · Post by **fgimian** » Mon May 14, 2007 6:40 am

Hey there, I really love this synth, congratulations on your achievement!

Here are my questions...

- Is there any way to perform FM between both oscillators ? If not, is this a planned feature for a future update?

- Is there a way to hard sync both oscillators ? If not, is this a planned feature ?

- Similar to above for Ring Modulation

- Do you plan on including waveforms other than analogue ? e.g. wavetables .etc ?

- When changing patches in Cubase SL 3.11, I get a pretty hard CPU spike which causes audio dropouts .etc. Can this be fixed ?

Best Regards

Lennard · Post by **Lennard** » Tue May 15, 2007 3:27 pm

Hi, to answer your questions:

soundpalace wrote:- Is there any way to perform FM between both oscillators ? If not, is this a planned feature for a future update?

Not yet, but you can do some FM using the LFO's already. Osc FM is planned for a future update indeed.

soundpalace wrote:- Is there a way to hard sync both oscillators ? If not, is this a planned feature ?

No, and it isn't planned (yet) either.

soundpalace wrote:- Similar to above for Ring Modulation

Not yet, but you can do AM (ringmod) with the LFO's already. Osc AM is planned for a future update.

soundpalace wrote:- Do you plan on including waveforms other than analogue ? e.g. wavetables .etc ?

Yes, there will likely be some more waveforms later.

soundpalace wrote:- When changing patches in Cubase SL 3.11, I get a pretty hard CPU spike which causes audio dropouts .etc. Can this be fixed ?

Are you using real ASIO drivers for your soundcard (and I don't mean Cubase's ASIO DirectX Full Duplex driver)? If not, please do so, or if not available try http://www.asio4all.com. That should fix the problem.

fgimian · Post by **fgimian** » Tue May 15, 2007 10:09 pm

Hi, I am using an Echo Audio Layla3G with the Echo ASIO drivers running at 6ms. I'm not using the DirectX / Multimedia drivers.

Lennard · Post by **Lennard** » Thu May 17, 2007 4:02 pm

That's strange, does it help if you change the buffer length a bit?

fgimian · Post by **fgimian** » Sat Jul 07, 2007 1:34 pm

Lennard, I'm so sorry for not responding, I have been so busy that I forgot about this thread

I tried it with higher buffer (12ms). Sometimes it hits the red when changing preset, other times it spikes to around 50% CPU and then comes down again.

If you'd like to me test out anything more, please let me know.

Revi111 · Post by **Revi111** » Sun Jun 13, 2010 6:59 pm

Hi there i use sylenth1 demo in comparison with other synths the quality of the sylenth sound is bad.Is it normal in demo mode?

Nielzie · Post by **Nielzie** » Sun Jun 13, 2010 7:08 pm

Revi111 wrote:Hi there i use sylenth1 demo in comparison with other synths the quality of the sylenth sound is bad.Is it normal in demo mode?

No it isn't a demo restriction as far as I know. Please define "bad sound". Do you hear crackles or pops or something like that?

There must be something wrong with your setup, because soundwise Sylenth1 is (still) one of the best sounding synths out there

Revi111 · Post by **Revi111** » Mon Jun 14, 2010 10:52 am

It sounds bad only when i load my preset.

Nielzie · Post by **Nielzie** » Mon Jun 14, 2010 1:49 pm

Revi111 wrote:It sounds bad only when i load my preset.

Then you'd probably better load other peoples presets

daniwin · Post by **daniwin** » Mon Jun 14, 2010 2:43 pm

Revi111 wrote:It sounds bad only when i load my preset.

...sure you're not using laptop speakers for monitoring?

Revi111 · Post by **Revi111** » Tue Jun 15, 2010 11:15 am

Nielzie was right it was my setup, it sounds nice and clear now ;)Thx cheers:)

LennarDigital

KVR Audio

Sylenth1 Demo, some questions :)