MuTools

sl23 · Post by **sl23** » Fri Mar 10, 2017 11:22 pm

Could someone please tell me if there is a way to use the MFO to adjust LFO destination via the front panel?
Or any other way to achieve the desired result?

Thanks

Taifunk · Post by **Taifunk** » Fri Mar 10, 2017 11:55 pm

you mean use an oscillator as a modulation source?

sl23 · Post by **sl23** » Sat Mar 11, 2017 10:37 am

Not tested it yet but used an MFO with various waveforms output to Audio to Mod converter and output that to various destinations, ie, Pitch Filter Volume, etc.

What I want is to be able to select a destination via the front panel. I know I could have several modules linked to each destination each with a front panel on/off switch. But this doesn't give easy hardware control. Like on the old Electribe and MC-909, you had a button that cycled through available parameters, like waveform, filter type, etc. This isn't possible in MuX, so the next best is to use a knob somehow to select the required destination. Is it possible?

bibz1st · Post by **bibz1st** » Sat Mar 11, 2017 11:00 am

Do you want one knob that can direct modulation to different destinations ?

sl23 · Post by **sl23** » Sat Mar 11, 2017 11:09 am

Yes, sorry if I didn't explain very well! Can that be done?

bibz1st · Post by **bibz1st** » Sat Mar 11, 2017 11:36 am

Yea, pretty sure that's easily sorted, can't try at the moment but I bet someone will come along and show how its done..
....taifunk....Andreas....looking at you

sl23 · Post by **sl23** » Sat Mar 11, 2017 12:20 pm

Thanks bibz

Perhaps things like this should be included as modular templates for use in larger projects?

bibz1st · Post by **bibz1st** » Sat Mar 11, 2017 12:34 pm

In fact Taifunk did make some switch mux's a while back, I have added them here.
EDIT
I remember now its not easy and yes a proper switch module would be nice, I think also Andreas and Dakkra showed how to fade between different destinations, that was with audio but I think the principal would be the same for modulation.

sl23 · Post by **sl23** » Sat Mar 11, 2017 1:31 pm

Thanks I'll give it a go

Taifunk · Post by **Taifunk** » Sat Mar 11, 2017 1:34 pm

Sorry for the delay guys

bibz1st wrote: I remember now its not easy and yes a proper switch module would be nice, I think also Andreas and Dakkra showed how to fade between different destinations, that was with audio but I think the principal would be the same for modulation.

I made two little example, the knob example seems to work but I do not know if this is implemented correctly by me,in addition there is another example that uses the on / off buttons

I usually use audiorate and some tricks to get different destinations for the modulations,
I'm going to check out the different options and try to make a template:)

Taifunk · Post by **Taifunk** » Sat Mar 11, 2017 4:15 pm

Seems that I managed to find a solution,1 input 4 output controlled by a single knob,(maybe I can add more out,I have to check)
I have to fix some things.

bibz1st · Post by **bibz1st** » Sat Mar 11, 2017 5:02 pm

Good work Taifunk, Ive changed a couple of the mod connection cables positive/negative settings so that the knob position corresponds with the correct mod number.

runaudio · Post by **runaudio** » Sat Mar 11, 2017 5:10 pm

bibz1st wrote:Good work Taifunk, Ive changed a couple of the mod connection cables positive/negative settings so that the knob position corresponds with the correct mod number.

download

Taifunk · Post by **Taifunk** » Sat Mar 11, 2017 5:14 pm

bibz1st wrote:Good work Taifunk, Ive changed a couple of the mod connection cables positive/negative settings so that the knob position corresponds with the correct mod number.

Well done bibz1st , you are right,feel free to change the patch

I mixed up some things.
I'm a bit busy at the moment but come back to work on the patch later or tomorrow:)

bibz1st · Post by **bibz1st** » Sat Mar 11, 2017 5:21 pm

No problem, we now have pads to select the correct mod outputs
Sorry runaudio, here it is...

MuTools

KVR Audio

Switch LFO destinations