KVR Audio

sprnva · Post by **sprnva** » Mon Dec 11, 2017 3:46 pm

In the meantime, you can change the URL to get the right Mac version.

nordickvr · Post by **nordickvr** » Mon Dec 11, 2017 3:49 pm

sprnva wrote:In the meantime, you can change the URL to get the right Mac version.

Thanks!

Wild Hades · Post by **Wild Hades** » Mon Dec 11, 2017 3:58 pm

nordickvr wrote:
Wild Hades wrote:Version 1.1.0 is now available here:
http://www.kvraudio.com/product/pteq-x-by-ignite-amps
...
Many thanks for the update.
Seems that linked Mac version is still 1.0.2 though?

Fixed, sorry!

Turello · Post by **Turello** » Mon Dec 11, 2017 10:04 pm

REAPER v5.62 (32 bit) on 64 bit Machine laptop don't recognize the VST3 version...

Wild Hades · Post by **Wild Hades** » Mon Dec 11, 2017 10:54 pm

Turello wrote:REAPER v5.62 (32 bit) on 64 bit Machine laptop don't recognize the VST3 version...

Just installed Reaper 5.62 32 bit on my Windows 10 64 bit machine, PTEq-X VST3 32 bit works perfectly.

Stupid question: are you sure you're trying to load the 32 bit version of PTEq-X and not the 64 bit version?

Turello · Post by **Turello** » Mon Dec 11, 2017 10:58 pm

Wild Hades wrote:Stupid question: are you sure you're trying to load the 32 bit version of PTEq-X and not the 64 bit version?

Si si, presi entrambi dal file zip/cartella 32 bit...

Compyfox · Post by **Compyfox** » Tue Dec 12, 2017 11:08 am

And here I thought the page is back up, after over 9 months. Apparently not - oh well

sfxsound3 · Post by **sfxsound3** » Tue Dec 12, 2017 11:39 am

Acknowledgement wrote:Best software Pultec imo, cheers guys!

Really?

WHY?

sfxsound3 · Post by **sfxsound3** » Tue Dec 12, 2017 6:13 pm

This is the default setting with all parameters to zero. What are those bumps at 200 Hz and 5 kHz? Should they be there?

e@rs · Post by **e@rs** » Tue Dec 12, 2017 6:50 pm

@200Hz = the nipple of a b00b. No idea about the other...

Tp3 · Post by **Tp3** » Tue Dec 12, 2017 6:52 pm

e@rs wrote:@200Hz = the nipple of a b00b. No idea about the other...

A potbelly

Aloysius · Post by **Aloysius** » Tue Dec 12, 2017 8:24 pm

I can confirm. It is a middle aged mans pot belly.

Wild Hades · Post by **Wild Hades** » Tue Dec 12, 2017 8:58 pm

sfxsound3 wrote:This is the default setting with all parameters to zero. What are those bumps at 200 Hz and 5 kHz? Should they be there?

Try to turn the "boost" knobs of the MEQ5 and see what happens...

In the digital world is not always a good idea to set a filter parameter to 0, because it can lead to a division by 0 somewhere and corrupt the state of the filter itself and the entire chain after it by filling memories with "inf" or "nan" values, which means no output until you reset the system state. Not good.

In my plug-ins, I usually avoid these situations by forcing parameter values to something a little more than 0, like 0.01, and this is what causes those peaks.

I find a "bump" of 0.02dB to be quite tolerable, though...

onerob · Post by **onerob** » Wed Dec 13, 2017 6:10 pm

Any chance of the other Ignite Amps plugins being updated to run as stably in AU format as PTEq-X?

Wild Hades · Post by **Wild Hades** » Wed Dec 13, 2017 7:22 pm

onerob wrote:Any chance of the other Ignite Amps plugins being updated to run as stably in AU format as PTEq-X?

Yes, The Anvil 3.0 is next.

[UPDATE 1.1.0] Ignite Amps PTEq-X VST/VST3/AU (Pultec MEQ-5 + EQP-1a + HLF-3C emulation)