Bitwig

MarkSutor · Post by **MarkSutor** » Wed Aug 12, 2015 4:32 pm

CnuTram wrote:Great stuff!

volker@bitwig wrote: IMPROVED - Shift + Click on the meter's peak value resets all the meter's peak values.

REALLY great stuff!

I remember asking about this so long ago! Super really great stuff.

TeotiGraphix · Post by **TeotiGraphix** » Wed Aug 12, 2015 4:38 pm

MarkSutor wrote:
CnuTram wrote:Great stuff!

volker@bitwig wrote: IMPROVED - Shift + Click on the meter's peak value resets all the meter's peak values.

REALLY great stuff!
I remember asking about this so long ago! Super really great stuff.

It's crashing right now....

Worked a couple times but now it just crashes with Shift + click.

Mike

Ogopogo · Post by **Ogopogo** » Wed Aug 12, 2015 4:44 pm

Is it possible to record into a group track? Or is the arm button just always greyed out?

TeotiGraphix · Post by **TeotiGraphix** » Wed Aug 12, 2015 5:03 pm

Ogopogo wrote:Is it possible to record into a group track? Or is the arm button just always greyed out?

No, but you would think that it should toggle all the recarm of the group's children? Or is that to dangerous for accidentally arming something.

Ogopogo · Post by **Ogopogo** » Wed Aug 12, 2015 5:14 pm

Thanks. Seems like a cool idea. Maybe it could work like the rec arm button in the inspector when you have multiple tracks selected. Showing the state of the child tracks, and stripes if only some are armed? Then you wouldn't have to worry about if any hidden child tracks were armed.

TeotiGraphix · Post by **TeotiGraphix** » Wed Aug 12, 2015 5:17 pm

Ogopogo wrote:Thanks. Seems like a cool idea.

Yeah I will probably mention it. The mute/solo work this way, they override the children's values but to not trash them.

Using the same logic, they could do this with recarm as well, if selected arms all children, if deselected, returns all children to their previous recarm state.

Ogopogo · Post by **Ogopogo** » Wed Aug 12, 2015 5:18 pm

Oops I edited too late.

garyboozy · Post by **garyboozy** » Wed Aug 12, 2015 5:18 pm

TeotiGraphix wrote:
MarkSutor wrote:
CnuTram wrote:Great stuff!

volker@bitwig wrote: IMPROVED - Shift + Click on the meter's peak value resets all the meter's peak values.

REALLY great stuff!
I remember asking about this so long ago! Super really great stuff.
It's crashing right now.... Worked a couple times but now it just crashes with Shift + click.

Mike

it's crashing here too when shift-clicking the meter's peak level in the Arrange/Inspector.
shift-clicking the peak level in Mix view (extended meters shown) doesn't crash, but doesnt seem to do anything at all.

(OSX 10.9.5)

goatgirl · Post by **goatgirl** » Wed Aug 12, 2015 5:19 pm

TeotiGraphix wrote:
Ogopogo wrote:Is it possible to record into a group track? Or is the arm button just always greyed out?
No, but you would think that it should toggle all the recarm of the group's children? Or is that to dangerous for accidentally arming something.

Actually you can. Usually there is no input selected for a group track, but if you set it to an input the group track will record to the group master track.

TeotiGraphix · Post by **TeotiGraphix** » Wed Aug 12, 2015 5:20 pm

Question for those routing gurus.

The image below, I have Maschine sending notes to the PolySynth(using the Arp in Maschine).

I would expect that during recording, I would hear the poly synth but the polysynth only plays when Rec of the arranger is deselected(and notes have been recorded into the clip), select it again, no signal from the polysynth. Has anybody seen this before?

Mike

MaschineRoute.JPG

goatgirl · Post by **goatgirl** » Wed Aug 12, 2015 5:26 pm

Love the new retro graphics on the sampler waveform display.

8 bit graphics.png

Ok, it's a graphic bug I found and its been reported

TeotiGraphix · Post by **TeotiGraphix** » Wed Aug 12, 2015 5:26 pm

goatgirl wrote:
TeotiGraphix wrote:
Ogopogo wrote:Is it possible to record into a group track? Or is the arm button just always greyed out?
No, but you would think that it should toggle all the recarm of the group's children? Or is that to dangerous for accidentally arming something.
Actually you can. Usually there is no input selected for a group track, but if you set it to an input the group track will record to the group master track.

Ah yes, that is a fact, this is getting hairy.

GroupRec.png

Ogopogo · Post by **Ogopogo** » Wed Aug 12, 2015 5:33 pm

goatgirl wrote:Love the new retro graphics on the sampler waveform display.

8 bit graphics.png
Ok, it's a graphic bug I found and its been reported

I've seen that before 1.2.

TeotiGraphix · Post by **TeotiGraphix** » Wed Aug 12, 2015 5:38 pm

Ok it seems I have learned something new today.

So a Group has a master audio track inherently. It overrides the child's signal.

In the below image, the polysynth only plays when the audio clip is absent.

To edit the actual Group's master clip, you must double click it in the arranger.

Mike

GroupMaster.JPG

maschinelf · Post by **maschinelf** » Wed Aug 12, 2015 5:46 pm

So how about making a birthday exception for beta access??

Bitwig

KVR Audio

Bitwig Studio 1.2 BETA 4